A rod for cleaning the barrel of a weapon. Modern methods for cleaning rifle barrels

Andrey L.
Cleaning a weapon is not an idle question for any shooter, be it a hunter, an athlete, a sniper or just an amateur. At the same time, there are a great many recipes for “correct” cleaning, and this topic is the reason for writing more and more new articles and heated debates. Despite the variety of existing methods and recommendations, it seems possible to highlight some general tips for cleaning weapons. In addition, with the gradual increase in popularity on the Russian market as new imported samples of high-precision rifled weapons, and various chemical care products, the appearance of an article devoted to methods for cleaning rifled barrels in the West seems very timely.

When firing from a rifle, as a result of the shot, both combustion products of gunpowder and the cartridge primer (carbon deposits) and sedimentation of bullet shell particles (copper plating) occur in the barrel as a result of the shot. It is immediately necessary to make a reservation that we will limit ourselves to primarily considering firing a bullet with a copper jacket and a non-corrosive primer from a non-chrome-plated barrel. Cleaning the barrel for other options (steel-jacketed bullets, lead bullets, chrome-plated barrels, etc.) does not differ significantly from the option under consideration, although some differences, of course, cannot be forgotten.

It is advisable to clean the rifle after finishing shooting, if possible without delaying it for too long. Despite the fact that modern Boxer capsules do not emit corrosive products during firing, when firing cartridges Russian production or military surplus ammo, in the vast majority of cases you will encounter corrosive Berdan primers. Moreover, experience shows that in good weather Spending an extra half hour at the shooting range cleaning a rifle is much more pleasant than doing it at home, often in a room poorly suited for such work with insufficient ventilation.

Accessories

To clean the barrel of a rifle, it is advisable to acquire the following accessories:

A good cleaning rod suitable for the rifle caliber. It is desirable that the cleaning rod be one-piece, with a plastic coating and a bearing in the handle. Dewey is considered the quality standard in the American sports shooting community, although there are analogues from other manufacturers.

Rice. 1. Various accessories and chemicals for cleaning the barrel

Visher, suitable for the caliber of the rifle (usually supplied complete with a cleaning rod).

Bronze brush for rifle caliber. As a rule, with proper regular care of the trunk, there is no need to use a brush. Moreover, cleaning chemicals can interact with the brush material itself, and the use of steel brushes in barrels High Quality highly undesirable.

Cotton flannel patches for cleaning the barrel (hereinafter referred to as “patches”). It is desirable that the size of the patches correspond to the caliber in such a way that when pushing the patch along the barrel, it passes under tension, that is, the force on the ramrod is felt, but is not excessive.

Guide bushing for cleaning rod, suitable for rifle bolt group. When cleaning the barrel with patches, bending the cleaning rod can lead to unwanted contact of the cleaning rod with the surface of the chamber or bullet entrance, which can have an extremely negative impact on the accuracy of the rifle. If possible, cleaning the rifle should be done from the breech - the quality of processing of the muzzle significantly affects the accuracy of the combat, so any contact with the muzzle is extremely undesirable. This is why, in addition to cleaning from the breech, it is recommended to push the patch along the barrel in one direction only, and to be extremely careful when pulling the cleaning rod back into the barrel from the muzzle. In cases where the design of the rifle does not allow cleaning the barrel from the breech (some semi-automatic models), it is strongly recommended to use a special cap to protect the muzzle from possible contact with the cleaning rod.

Carbon remover. Hoppe's No.9 Bore Cleaner (the choice of reconnaissance snipers of the US Marine Corps) has proven itself well; other brands include Kroil, Break-Free, and Shooter's Choice.

Copper remover. These cleaners can be divided into two groups - weak alkaline (a typical example is Hoppe's Benchrest Copper Remover) and strong ammonia (such as Sweet's 7.62). The products from the first group, although significantly weaker in terms of removing copper plating, are more gentle on the trunk itself than the potent products from the second. Thus, Sweet 7.62 is not recommended to be left in the barrel for more than 15 minutes, while Hoppe's can be left in the barrel for several hours to combat severe copper plating.

A cradle, slipway or machine for holding a rifle. When cleaning the rifle, it must be firmly fixed so that the cleaning rod can be pushed through with force. If the rifle is equipped with a bipod, it is enough to use it. It is advisable that the barrel of the rifle be slightly tilted forward when cleaning to drain the chemicals.

Cleaning the rifle

The cleaning procedure begins with removing the bolt from the rifle (for bolt-action rifles) and installing the guide sleeve in its place. Often these bushings use a bolt retention system or bolt handle opening to securely lock into the bolt group. Sometimes the bushing is equipped with a rubber seal to prevent chemicals from leaking from the rifle barrel into the chamber and bolt group.

Rice. 3. The sleeve is inserted into the receiver and held by the opening for the release handle

Once the sleeve is securely installed in the chamber, you can proceed directly to cleaning the barrel. You should start by removing carbon deposits - the most easily cleaned component of contamination. To do this, you need to soak one patch in a cleaning agent, then put it on the visher and smoothly drive it through the bore. The easiest way to remove a dirty patch that appears from the muzzle (each patch is used only once!) is to place a garbage bucket under the muzzle - the patch will fall off the visor itself when the cleaning rod is pulled back. This procedure must be repeated several times, each time coating a new patch with a cleaning compound, until the patches come out of the barrel clean (or there are no obvious improvements in the quality of the emerging patch).

Rice. 4. A clean patch is put on the visher and pushed into the barrel through the bushing from the breech

Now you can proceed to removing copper plating from the barrel. The procedure itself in this case is similar to cleaning carbon deposits, but there are several differences. Of course, in this case, a copper remover is used. After running the first two or three patches, generously moistened with an anti-copper solution, you can pause for a few minutes to give the solution time to oxidize the copper deposits. The next time you run the treated patch along the trunk, it will show characteristic blue-green traces of copper oxides. This procedure must also be repeated until the patches come out of the barrel clean.

Rice. 5. At the exit from the barrel, a patch with traces of carbon deposits is removed from the cleaning rod during the reverse stroke

If it is not possible to completely get rid of copper in the trunk, there are several options for further action. The simplest is to treat the barrel with a cleaning agent and leave it to “soak” for 12-24 hours (it is advisable to place the rifle with the barrel down, resting it on a rag, which will absorb the solution flowing from the barrel). After such chemical treatment, copper is removed from the barrel much easier. The second option is to use stronger ammonia-based products (under no circumstances leave in the trunk longer than prescribed by the manufacturer!). The procedure for their use does not differ from that described above for weaker alkaline ones. And finally, you can try using a brush (under no circumstances a steel one!) to remove copper from the barrel. When using a brush, it is recommended to treat it with a cleaning agent, then make about 10 reciprocating movements through the sleeve, smoothly moving the brush along the entire length of the barrel. It is necessary to observe maximum caution and smoothness at the moment when the brush enters back into the barrel from the side of the muzzle - the quality of the cut is crucial for the accuracy of the rifle's fire.

Rice. 6. Some bushings allow you to wet the patch already on the cleaning rod through a special hole in the bushing - in this case, powerful Sweet's 7.62 is used

After completing the cleaning procedure, it is necessary to drive a dry patch through the barrel. If you find no traces of copper on it (very faint traces), the barrel cleaning is complete. Next, you need to run a few more untreated patches through the barrel until they come out completely dry, and, if the rifle is to be stored for a long time, run one or two patches with preservative lubricant through the barrel (in this case, before shooting, the lubricant must be removed with two or three dry patches ).

There are often cases when it is not possible to completely clean a rifle barrel of copper using the methods described above. This usually happens with rifles that have been improperly or irregularly maintained, or rifles with an unbroken barrel. In this case, you can try the barrel break-in procedure described below. There are examples when running-in improved the characteristics of even barrels with significant preliminary firing. There is a more radical way to clean the barrel - using abrasives, type J-B Cleaner, however, opinions about the benefits and harms of using such products differ greatly and therefore it is not possible to definitely recommend them for use. If no cleaning really helps severe copper plating, there is a method of electrochemical cleaning, but using it at home is extremely difficult and therefore this method is beyond the scope of this article.

Barrel running in

The inner surface of the barrel of almost any new rifle is imperfect (the exception is hand-polished one-piece barrels) and has pores and irregularities left as a natural result of the barrel manufacturing process. When firing, these pores are gradually smoothed out, but at the same time they are filled with copper from the bullet casing, which leads to a strong increase in the rate of accumulation of copper deposits - as a result, the number of shots fired from the rifle without loss of accuracy due to copper plating will be small, and the barrel will be completely cleared of copper is often simply impossible.

To avoid filling the pores and micro-irregularities of the barrel with copper, it is recommended to carry out the barrel running-in procedure according to the following algorithm.

Fire one shot from a new rifle, after which the barrel must be cleaned of copper according to the cleaning procedure described above. This process (cleaning after each shot) must be repeated several times until the copper plating after the shot clearly decreases.

Next, you need to move on to shooting in series of several (in different sources the specific figure varies from 2 to 5) shots, after each series it is again necessary to clean the barrel from copper deposits. The number of series should also be determined by the apparent reduction in copper plating after the series.

Then you need to lengthen the series to 10-20 shots between cleanings, and after several such series the barrel of your rifle will be broken in.

It is not possible to find an exact technical description of the processes occurring in the barrel during break-in of a rifle in the literature, however, apparently, the break-in process is a gradual polishing of the barrel by firing while simultaneously removing copper from the pores and irregularities. This interpretation explains both the improvement in the quality of the new barrel after break-in, and the benefit of running-in barrels that have already been shot but not run-in.

Individual approach

Rice. 7. Cleaning your rifle at home

There are many legends, myths and beliefs associated with barrel cleaning procedures. Someone considers it unacceptable to use coated cleaning rods, due to the deposition of abrasive combustion products on this coating, which scratch the barrel as the cleaning rod passes (to the question, “Why will these abrasives scratch a steel barrel and not a softer plastic coating?”, the answer is received usually fails); someone considers the use of potent agents in stainless steel barrels unacceptable; someone pushes the ramrod along the barrel only 5-10 cm at a time, and considers feeding the ramrod in one smooth movement absolutely unacceptable; The list can be continued almost endlessly. An article recently appeared in one of the American weapons publications in which the author deliberately subjected his rifle to numerous cleanings in the worst possible way - without a bushing, with a composite aluminum cleaning rod with a steel brush and a terrible pot of chemicals - and was convinced in practice that after such “bullying” the accuracy of the battle his rifle has not deteriorated. All these facts speak only about one thing - cleaning the rifle, except practical lesson is also a ritual that will certainly be unique to each shooter, different from all others. In this case, all of the above are just some general considerations, in accordance with which the process of cleaning a rifle can be structured in such a way that it brings both benefit to the barrel and satisfaction to the shooter himself.

Do you remember that Leskov’s Lefty asked him to tell the Tsar Father that the soldiers should not clean their guns with crushed bricks? Look, when in Rus' they started thinking about the abrasive properties of ceramics and the right technologies cleaning weapons!

Seriously, not so long ago, in remote places, trunks were simply “soaked” with boiling water, then chased away with a brush and wiped dry. But do not rush to accuse your ancestors of barbarism. The same operation is carried out for modern pneumatics for collective use in very advanced cases, when the barrel is so leaded that no chemicals or mechanical devices can handle it. Physics comes to the rescue: due to the difference in thermal expansion coefficients, lead flakes safely peel off from the steel.

I think that among the readers there are no enthusiasts of a bubbling kettle or, God forbid, an electric drill as a drive for a brush. And yet, how to properly clean a weapon and with what?

Professionals and amateurs: the difference in approaches

The author belongs to the group of “moderates” who believe that excessive enthusiasm for cleaning and lubrication, especially without a critical understanding of the essence of the processes, also does not lead to good. This is mainly due to long-standing experience, when shooters had at their disposal kerosene (then the super-product WD-40), an alkaline compound and neutral oil. Weapons maintained with the help of these components have served faithfully and continue to serve for many decades, failing for reasons not related to the chemistry used and the frequency of hygiene procedures. I note, however, that all this applies to serial domestic shotguns, albeit high-quality ones, as well as to civilian versions of army rifles - OP-SKS, "Tiger", numerous "Kalashoids".

With the advent of specialized chemicals, especially aerosol ones, on our shelves, everything has become even simpler. For example, the same legendary “Ballistol” allows you, after a day full of shooting and rain, to simply wipe all the iron, fill it inside and outside with this spray and not worry about anything else until you get home, where you can clean it in a more comfortable environment.

And finally, “maximalists”, most often fans of high-precision shooting. People of this type practice thoroughness in everything. As a rule, they prefer a table covered with newspapers, albeit a compact one, but still a center for cleaning. For example, such as in the photo, the extremely inexpensive “Portable Maintenance Center”.

And it’s hard to disagree with them. Look how thoughtfully and conveniently everything is done.

When you read the recommendations of adherents of “high precision”, you are amazed at the perseverance and scrupulousness, the purely scientific approach to removal different types pollution. Can you imagine what kind of practical experience and surgical precision of movements you need to have in order to remove copper plating on match barrels using abrasive pastes!? Their arsenal of techniques includes, for example, the selection of chemicals for cleaning different AREAS of the chamber, methods that provide for special cleaning after EVERY shot, the use of substances that are neutral to some barrels, but literally dissolve the metal of others. In a word, if you have a burning desire to become a real BR shooter, you shouldn’t engage in guerrilla warfare - come out of the forest to people and join a team of like-minded professionals. Moreover, there is no “benchrest” without regular competitions.

For the majority of people, all this is somewhere on the other side of good and evil. Therefore, let us be guided by the condition “necessary and sufficient” known from mathematics. Without stopping at the basics of preliminary procedures, such as the need to unload and disassemble the weapon, prepare all the necessary accessories, etc., the entire cleaning process can be divided into three stages.

Stages of cleaning weapons

filling with an alkaline composition (solvent) everything and anything that came into contact or could come into contact during the firing process with the primer, cartridge case, bullet and, of course, powder gases;
actual cleaning;
lubrication and preservation of weapons.

Start over.

For the vast majority of cases and non-exclusive weapons, the already mentioned “Ballistol” or the well-known “Hoppes No. 9".

There are many more modern drugs with similar effects, there are much more effective ones, for example, Shooter’s Choice formulations, but many of them are highly specialized. For example, they can only be used for stainless steel barrels. If you are the owner of such a weapon, which is not too widespread, carefully study the manufacturer’s recommendations.

So, the composition we have chosen is applied to all areas to be cleaned - the barrel bore, the bolt, the mirror (at the smoothbore), the gas outlet parts, the outside of the barrel - 5-6 centimeters from the cut. We leave the entire household to soak for 10-20 minutes.

Let's move on to the actual cleaning. Here we will need tools

Toolkit closely related to weapon features

Ramrod.

Somehow it has long been the custom that for a rifled weapon it must be one-piece, for a smooth-bore weapon it makes no difference, but more often it must be composite. The approach is correct, taking into account the caliber: you never know what can happen in a long tube, the internal diameter of which is less than a centimeter, so the requirements for strength characteristics in the first case are increased.

The cleaning rod material is also different. For a smooth bore, wood and brass are quite suitable; for a rifled bore, only metal, always braided, although bending-resistant and relatively safe stainless steel products are available on sale. Do not use aluminum devices under any circumstances; the oxide covering them has abrasive properties comparable to crushed brick.

Another required condition for rifled barrels: the cleaning rod itself must rotate freely on a bearing installed in the handle, so that the cleaning devices, when moving back and forth, follow the rifling strictly.

Actually, ideally these options look something like this:

On the left is a cleaning rod for smooth-bore calibers, two-section, length 86 cm, the set includes a classic SL visher attachment. On the right is a cleaning rod for rifled weapons. 35 cal., 9 mm and above, single-section, with bearing, length 91 cm.

Visher and patches.

The chamber and the barrel cut are “ sacred cows” and should be treated accordingly. Therefore, the movement of the cleaning rod with the wiping material (patch) always goes in one direction - from the breech to the barrel. The insertion itself must be extremely careful, and the contaminated patch must be removed from the visher upon exiting the barrel. It is very convenient to do this with vishers of modern design. Compare: on the left is the classic type, familiar to almost all shooters, on the right is the brass .22/.223 cal.

Agree, it is very convenient to pin a branded or homemade patch on the latter (a square or round piece of cotton fabric, selected for the caliber), which, upon exiting the barrel, will simply fall off and fall into a carefully placed container.

Cutting defects will also not add accuracy to a smoothbore gun. And here, willy-nilly, you will have to use a traditional visher, into the slot of which a cloth of suitable size is threaded and loosely wound.

Cleaning guides.

Somewhat ambiguous devices that serve to protect the chamber, the bullet entrance and the cut of the barrel of a rifled weapon.

The photo shows guides .30 ABS3 and .30 C30.

Let's start with the second one, for cutting the trunk. The scope of its application is extremely narrow, mainly for some models, and all because, as we remember, the barrel is cleaned only from the treasury to the barrel. There are rifles where the manufacturer, as if on purpose, did everything to make access to the breech difficult. But even here it is better not to resort to technology turned 180 degrees.

The guides inserted instead of the bolt, according to authoritative shooters, with rare exceptions do not provide accurate centering of the cleaning rod, since they are made universal for a certain caliber. Meanwhile, each rifle has its own characteristics. In a word, it’s easier to protect the USM from dripping reagents with a cloth, and center the cleaning rod by eye; the main thing is not to rush or get nervous. Or thoughtfully, again without rushing, choose a guide strictly for your weapon.

Ershik.

In the photo: brass and hard nylon brushes, 30 and 12 gauge, as well as a puff, which serves both for lubrication and for removing excess oil.

There are also brushes for cleaning the chamber. As a rule, they come as part of cleaning kits, but they can also be purchased separately, even on a handle.

And one more thing: brushes are used only when dry, otherwise they are immediately covered with abrasive particles and only aggravate the process of destruction of the barrel mirror.

"Lifesaver"

You definitely won't be able to do without this device. Essentially, this is a kind of miniature hybrid of a spatula and a toothpick, carved from wood. It is with them, sometimes with a wrapped rag, that you will clean dirt from hidden places, of which there are plenty in the weapon, or carefully remove the remaining copper from the mirror of the end of the receiver (where the firing pins are).

The weapon is “soaked”, let’s start cleaning

Blessed are the owners of classic break-in shotguns and other kiplaufs, as well as modern semi-automatic rifles. It’s more difficult for the rest - you can’t unfasten the barrel, and here the already mentioned branded cleaning center could be a great help. The basic rule: in a machine or just on a table, the barrel should point down so that all the nasty stuff does not flow into the weapon’s mechanisms.

So, we put a patch on the visher (twist a rag) and in one leisurely movement we push the cleaning rod forward. We discard the contaminated patch and carefully remove the cleaning rod. We alternate patches with brushes (only on dry trunks). We clean the chamber with rotational movements, under no circumstances trying to push a special brush into the bullet entrance. If necessary, treat the barrel with the cleaning compound again.

And so on until we achieve results. Professionals carefully evaluate contaminants, using specialized chemistry depending on their types.

For the average shooter, all this is more interesting in theoretical terms. Or when changing ammunition. So that you can say: “This is dirty!” And don't contact him anymore.

Our task is simple: regardless of whether the copper on the patches turns blue or matte remains of polyethylene in the sleeve are found, we must ensure that the cleaning material at the exit does not differ from what was at the entrance. That's all. Depending on the degree of contamination, all procedures can take ten minutes or an hour.

Lubrication and preservation

Finally, the patches emerge from the trunk pristinely clean. And it’s the turn of neutral oil. By and large, we use it to remove not so much dirt as the remnants of cleaning substances, including from metal micropores. Suspicious marks will again appear on the patches. After they disappear, apply a thin layer of neutral oil to the now dry trunk with a lightly lubricated patch, cloth, or powder puff. Or a preservative composition - depending on your goals and objectives. For example, Rust Prevent Corrosion Inhibitor or Elite Hoppe's GO4.

It is highly advisable to repeat the second stage of cleaning (with neutral oil) after three to four days, maximum a week. This is how long, on average, the sweating of contaminant residues from the deepest microcracks continues.

I would like to repeat it again. With the modern variety of weapons, carefully read the manufacturer’s recommendations if you have, say, a stainless or chrome-molybdenum barrel. And select cleaning compounds, especially aggressive ones, strictly in accordance with them. Do not always trust opinions from the Internet; if you read carefully, they often contradict each other. In a word, be careful and careful.

Let's assume that before the very first shot the barrel bore is absolutely clean - there is no dust, no lubricating oil residue, no old dirt. In this case, the first layer of new contamination will be the trace from the casing of the first bullet, which will pass through the bore when firing.

Modern rifle bullet casings are made from a wide variety of materials. Next, we will consider in detail the types of contaminants left by each specific jacket material, but for now we will focus on the fact that all bullet jacket materials, without exception, leave a mark in the barrel. This mark is a heterogeneous film that adheres tightly to the surface of the bore. The next bullet will leave a film on top of the film from the first bullet; and the more times you fire your weapon, the more extensive and thicker this cumulative film of bullet casing becomes.

The matter is aggravated by the fact that the material of bullet casings is not the only factor determining the contamination of the barrel bore, and not even the main one. The greatest influence - and the greatest harm - is caused by the gaseous combustion products of the powder charge and primer composition. Powder gases develop enormous pressure when fired; Thanks to (although it is ungodly to thank them for this) this pressure, gaseous combustion products are able to penetrate into the crystalline structure of the barrel steel and accumulate there. And since powder gases and, especially, combustion products of the primer composition have an aggressive chemical effect on the metal of the barrel bore, this effect is the most deplorable for the barrel.

Solid combustion residues of the powder charge and primer composition settle on the surface of the barrel bore. Since there is already a film left by the bullet casing, the shooting results in the formation of something that looks like a layer cake - namely, a dense multi-layer film of aggressive dirt.

Should we be afraid of this dirt?

There is a fairly large community of shooters (mainly made up of hunters who shoot from long-barreled rifles not too often - only during the hunting season - and quite a few), which do not bother with cleaning at all. In this environment, it is generally accepted that pollution does not harm the trunks at all. And it is considered especially chic not to clean a barrel that has military origin. I myself have so often heard statements like “I don’t clean my SKS (SVT/Tiger/Vepr/Saiga/three-line, etc.) at all - why?” that it now causes an allergic reaction in me.

In fact - and this should be learned by heart - gunshot contamination is harmful to all rifle barrels without exception, regardless of the coating or lack of coating of the bore, the type of barrel steel, the celebrity of the manufacturer and the cost of the weapon. But there is no need to be afraid of this dirt. Why? Because now we will learn to fight it.

To effectively combat rifle barrel contamination, you will need some tools.

First of all, this is a ramrod. A cleaning rod is the cornerstone of proper cleaning of a rifle barrel, since the design of the cleaning rod determines not only whether your rifle will be properly cleaned. A bad cleaning rod will not damage the bore for long; if you want to avoid this, then you need a one-piece cleaning rod - in the form of a non-separable metal rod in a plastic shell - and as rigid as possible. The best rifle cleaning rods fully comply with the concept of an “ideally rigid rod” used in theoretical mechanics - there is no bending, and the force is transmitted only in the axial direction.

Of course, you can use composite cleaning rods or solid ones, but made of polymer materials. However, composite cleaning rods, even those coated with plastic, can scratch the edges of the rifling in areas where individual links meet; a similar phenomenon can occur when using solid, but flexible, polymer cleaning rods. Since we agreed to love our guns, it should be understood that a rifle cleaning rod should not be flexible. This is not a spinning rod, after all.

The cleaning rod must also be long enough - we should not forget that the rifle, in addition to the regulated length of the barrel with chamber, usually also has a receiver. Plus, sometimes it's useful to be able to swing. I myself use a cleaning rod with a working length of 44 inches (with a rifle barrel length with a chamber of 26 inches) and do not experience any inconvenience when cleaning - on the contrary, it is just a pleasure.

An equally important tool is the bushing (in English-speaking countries it is called bore guide). I would even say that the bushing and cleaning rod share first place in importance.

The sleeve has a dual function. Firstly, it really serves to guide the movement of the ramrod - or rather, to prevent the ramrod rod from touching (and thus possible damage) the rifling in the area of the bullet entry of the barrel. This is very important, since the accuracy of the weapon directly depends on the condition of the rifling in the area of the bullet entrance. Second, a bushing that fits tightly into the rifle's chamber prevents cleaning chemicals and dissolved dirt from getting anywhere other than the rifle's bore. Agree, there is no point in spreading the dirt removed from the bore all over the weapon.

The remaining tools are a variety of attachments. All attachments can be divided into two main types: brushes and wipers (also known as “vischers”).

The purpose and principle of operation of brushes is simple and clear - they are needed for mechanical impact on a dense film of contamination. There are metal brushes (usually brass or bronze) and polymer.

Of course, you won’t be able to remove dirt with just a brush, just as you won’t be able to eat a bowl of soup with a fork - that’s what wipes are for.

And the rack (gun vise or gun cradle) closes the group of necessary instrumentation. It is designed to secure your rifle (or a separate barrel with receiver) during cleaning. There are specialized racks; There are racks integrated into folding tool boxes. In addition, you can make the stand yourself - it’s not that difficult. In any case, a stand is necessary - at least even for the convenience of the shooter himself.

In addition to tools, it makes sense to describe consumables. The most common of them (and at the same time, perhaps the simplest and most convenient) are fabric patches (from the English Patch - shred, shred). You can make them yourself by cutting a piece of fabric with scissors into squares of the desired size, or you can buy ready-made ones; but homemade patches are better for cleaning because you can, by adjusting the size of the patch you cut, adjust the tightness of its passage through the barrel, while factory-made patches in the package are usually the same size. It is best to make patches from fabric white- dirt is more noticeable on it, - and thick and soft enough for the patch to completely fill the cross-section of the barrel bore. Some time ago I myself solved the problem with patches on a grand scale, having bought about thirty meters of white flannel.

Recently, consumables produced by VFG have become very famous - in the form of felt cylinders screwed onto a special wipe (they are popularly called “VFG patches”, although this is incorrect - these cylinders do not at all resemble shreds). These cylinders are indeed very convenient - and in some procedures they are generally irreplaceable - however, they are not convenient for everything, and cannot completely replace fabric patches. Therefore, it would be most reasonable to use both patches and cylinders - the procedure will be described below.

Now is the time to move on to a description of the chemicals used for cleaning.

All necessary weapons chemicals can be divided into three categories based on their operating principle. Firstly, these are means for dissolving and neutralizing powder deposits. Secondly, these are products for removing traces of bullet casing material - I deliberately do not say “copper”, since such products, as a rule, can also dissolve traces of lead and zinc. There are also universal products that simultaneously dissolve both carbon deposits and traces of metals, but their effect, as a rule, is somewhat weaker.

The third category includes cleaning pastes - an approximate analogue of cosmetic scrubs. As a rule, such pastes have an exclusively mechanical principle of action, but there are also pastes with a complex anti-copper-mechanical effect. Unlike solvents, pastes perfectly clean even those barrels from which bullets with coatings were fired - such as molybdenum disulfide (moly-coated) or Teflon-based coatings, which are not removed by conventional chemistry.

And finally, the fourth category consists of penetration and lubricating oils. The task of oils is not only and not so much lubrication itself. It is much more important to neutralize the remnants of cleaning chemicals, which in themselves - especially products from the second category - are very aggressive. Such oils must have high fluidity and penetration in order to neutralize aggressive substances wherever possible; that is why they are, in fact, called penetration (from the English Penetrate - to penetrate inside, to pierce). Moreover, these oils are also excellent for lubrication.

It should be noted that in the most extreme cases - for example, when you are far from civilization and there are simply no suitable means at hand - penetration oil can also be used to neutralize powder deposits. Of course, it won’t work nearly as effectively as a specialized carbon remover, but it’s still better than not cleaning at all.

Very often questions arise: is it possible to clean weapons with kerosene or its derivatives, like WD-40?

I will answer this evasively, because I know: many people clean only with WD-40, resolutely sweeping aside all advice and ridiculing supporters of specialized gun cleaning products. Yes, you can clean your gun with WD-40. You can also clean your weapon with cucumber brine or stale Zhigulevsky beer - and just try to say that I’m wrong. Can. But it's not necessary. Believe me.

Now it's time to reward you for your patience and indulgence in my tediousness. Let's move on to cleaning.

First of all, stock up on everything you need. You already know that you need a stand, cleaning rod and bushing. Additionally, you will need one bronze brush, one plastic brush, one wiper for fabric patches, one wiper adapter for VFG felt cylinders, one piece of flannel, one handful of VFG cylinders, one pack of cotton swabs for cleaning ears, one roll of paper towels or 65 meters toilet paper, and one nail file. Don't forget also two arms and one head.

We will use only the chemicals that are on sale in Kyiv weapons stores. We will need one can of Forrest foam, one can of Hoppe's #9 Nitro Powder Solvent, one can of Robla Solo Mil, one can of cleaner J-B pastes Bore Cleaner and one bottle of Klever Ballistol spray. Instead of Robla and Hoppe #9, you can successfully use Shooter’s Choice MC #7 Firearms Bore Cleaning Solvent - this product dissolves both carbon deposits and traces of metal equally well.

So. Let’s say you’ve just shot at the shooting range (or shot a prize-winning moose while hunting, drank “on the blood” and took photos) and intend to go home (or go to the base to “ferment”). Of course, the first thing you think about is your weapon (assuming this is true).

If you shot only a few times, and you plan to start the main cleaning of the weapon the next day - as is usually the case on group hunts - there is no point in pouring chemicals into the barrel; it will do more harm than good. It is enough to remove the bolt and drive a loose patch through the barrel, generously moistened with Ballistol. This oil has a slight alkaline effect, so it is able to somehow neutralize powder deposits - which, in fact, is what we need.

In the case when the shooting is large - fifteen shots or more - and the journey home will take no more than an hour or two, it makes sense not to limit yourself to Ballistol. If you were shooting metal jacketed bullets, blow Forrest foam into the still hot barrel and leave it like that. Due to the increased temperature, the effect of the foam will be enhanced, while there will be no danger to the trunk - Forrest foam is a very delicate product.

At home, mount the weapon in the rack and insert the bushing into the receiver.

If the bore was lubricated with Ballistol, then it must be thoroughly wiped off - otherwise Ballistol will weaken the effect of the solvents; the same thing, but for a different reason, should be done with foam. It is best to do the first wiping with a VFG cylinder - there is still a lot of dirt in the barrel (after foam there is, naturally, much less dirt than after Ballistol, but Forrest causes the dirt to swell in some way), and a regular patch will not help much. Pass a couple more cylinders through the barrel.

Now it's the turn of the pipe cleaners. Take a plastic brush and use a nail file to apply some JB paste to it (the paste should only cover the middle part of the brush). Insert a cleaning rod with a brush into the barrel and move it back and forth several times (at the exit from the barrel, the brush should completely leave the muzzle). Now remove the brush - you won't need it anymore - and wipe the cleaning rod clean of dirt. Remove the spent paste mixed with dirt from the bore completely - first in cylinders, then in patches.

Now your trunk is cleaned of the main dirt; however, the most disgusting and complex dirt remained in it. I'm talking about soot that has eaten into the pores of the metal of the barrel due to the monstrous pressure developed during the shot. The complexity of this contamination is that it is hidden under a thin film of metal left by bullet casings - the very first metal film, which cannot be completely removed using a non-abrasive paste.

Solvents will help us in the fight against this film (in fact, Forrest foam itself is such a solvent, but in this case we need something more serious). Run several patches through the barrel, generously moistened with Robla or Shooters Choice, and leave the barrel alone for about half an hour (but no more, since these products containing ammonia compounds are quite aggressive).

After half an hour, wipe the barrel dry with patches. Apply a little paste to the side of the VFG cylinder using a nail file - just a little bit. Pass this cylinder back and forth along the barrel a dozen times - making sure, however, that the cylinder does not extend beyond the muzzle. This procedure will help clean off any remaining metal film that has not been completely dissolved by the chemical.

Now you need to neutralize the remaining chemicals with Ballistol. After letting the Ballistol run for half an hour or so, you need to wipe the barrel clean and dry using patches (if three patches in a row come out as clean as what came in, then you've done your job).

Now that there are no solvents left in the bore, you can use a bronze brush (otherwise it would be successfully dissolved by chemicals). A bronze brush is not needed to destroy dense dirt - we have successfully overcome it with the combined action of a plastic brush, felt, paste and chemicals. Due to its rigidity, a bronze brush is needed to destroy dirt in hard-to-reach areas of the barrel, where it is almost impossible to “get it” with more delicate means: we are talking about the angles of the rifling. A few - a dozen or a little more - movements back and forth are enough; then you need to pass several patches moistened with solvent. Then you need to wipe the barrel clean with dry cloth patches until they no longer come out dirty. Voila - your trunk is thoroughly cleaned.

It is convenient to clean the remaining components of your weapon using cotton swabs moistened with Ballistol, and the same patches used as napkins. Compared to cleaning the bore, cleaning the remaining components of the weapon does not present any difficulty, so I will not dwell on it in detail.

There is some subtlety in cleaning the barrel if you shot coated bullets - like molybdenum disulfide or some types of Teflon.

The difficulty here is that traces of these coatings are not dissolved by conventional means. You will have to use exclusively mechanical means - brushes and paste; Therefore, when buying such cartridges, be patient.

Long life to you and your weapon.

Andrey Rudoy

Do you remember that Leskov’s Lefty asked him to tell the Tsar Father that the soldiers should not clean their guns with crushed bricks? Look, when did people in Rus' think about the abrasive properties of ceramics and the correct technologies for cleaning weapons!
Seriously, not so long ago, in remote places, trunks were simply “soaked” with boiling water, then chased away with a brush and wiped dry. But do not rush to accuse your ancestors of barbarism. The same operation is carried out for modern pneumatics for collective use in very advanced cases, when the barrel is so leaded that no chemicals or mechanical devices can handle it. Physics comes to the rescue: due to the difference in thermal expansion coefficients, lead flakes safely peel off from the steel.
I think that among the readers there are no enthusiasts of a bubbling kettle or, God forbid, an electric drill as a drive for a brush.

How to properly clean a weapon

In order to avoid omissions, let’s say right away that there are a lot of legends, myths and opinions in this area of knowledge. The most radical of them: cleaning weapons is harmful. As a rule, it is followed by those who have ruined the barrel or bolt group through incorrect actions, for example, the wrong choice of lubricant. Or - you will laugh - owners of models with extremely difficult disassembly/assembly and access to the breech.
The author belongs to the group of “moderates” who believe that excessive enthusiasm for cleaning and lubrication, especially without a critical understanding of the essence of the processes, also does not lead to good. This is mainly due to long-standing experience, when shooters had kerosene at their disposal (then spray WD-40), alkaline composition and neutral oil. Weapons maintained with the help of these components have served faithfully and continue to serve for many decades, failing for reasons not related to the chemistry used and the frequency of hygiene procedures. I note, however, that all this applies to serial domestic shotguns, albeit high-quality ones, as well as to civilian versions of army rifles - OP-SKS, « Tiger", numerous " Kalashoids».
With the advent of specialized chemicals, especially aerosol ones, on our shelves, everything has become even simpler. Let's say the same legendary " Ballistol"allows you, after a day full of shooting and rain, to simply wipe all the iron, fill it inside and out with this spray and not worry about anything else until you get home, where you can clean it in a more comfortable environment.
And finally, “maximalists”, most often fans of high-precision shooting. People of this type practice thoroughness in everything. As a rule, they prefer a table covered with newspapers, albeit a compact one, but still a center for cleaning. For example, like the one in the photo, extremely inexpensive Portable Maintenance Center.

And it’s hard to disagree with them. Look how thoughtfully and conveniently everything is done.
When you read the recommendations of adherents of “high precision”, you are amazed at the perseverance and scrupulousness, the purely scientific approach to removing various types of contaminants. Can you imagine what kind of practical experience and surgical precision of movements you need to have in order to remove copper plating on match barrels using abrasive pastes!? Their arsenal of techniques includes, for example, the selection of chemicals for cleaning different areas of the chamber, methods that provide for special cleaning after each shot, and the use of substances that are neutral to some barrels, but literally dissolve the metal of others. In short, if you have a burning desire to become a real shooter" Benchrest“, you shouldn’t engage in partisanship - come out of the forest to people and join a team of like-minded professionals. Moreover, “Benchrest " there is no such thing as regular competitions.
For the majority of people, all this is somewhere on the other side of good and evil. Therefore, let us be guided by the condition “necessary and sufficient” known from mathematics. Without stopping at the basics of preliminary procedures, such as the need to unload and disassemble the weapon, prepare all the necessary accessories, etc.

Basic steps when cleaning weapons

filling with an alkaline composition (solvent) everything and anything that came into contact or could come into contact during the firing process with the primer, cartridge case, bullet and, of course, powder gases;
actual cleaning;
weapon lubrication.

For the vast majority of cases and non-exclusive weapons, the already mentioned “Ballistol” or the well-known “ Hoppes no. 9».

The first one is extremely convenient to use, since it is made in the form of an aerosol, it quite successfully copes with all contaminants, including lead and copper plating, while being absolutely safe. And not only for the wood or plastic of the stock, but also for your hands. Moreover, according to the manufacturer and numerous users, it has a bactericidal and generally beneficial effect on the skin. "Hoppes", on the contrary, is very toxic, so the author does not really like its relatively rare aerosol version. You can grab a dose even in the fresh air. It copes with its direct responsibilities perfectly, perhaps better than Ballistol.
There are still a lot of modern drugs with similar effects, there are much more effective ones, for example, formulations Shooter's Choice, but many of them are highly specialized. For example, they can only be used for stainless steel barrels. If you are the owner of such a weapon, which is not too widespread, carefully study the manufacturer’s recommendations.
So, the composition we have chosen is applied to all areas that need to be cleaned - the barrel bore, the bolt, the mirror (at the smoothbore), the gas outlet parts, the outside of the barrel - 5-6 centimeters from the cut. We leave the entire household to soak for 10-20 minutes.

Cleaning weapons

Here we will need tools that are closely related to the characteristics of the weapon. Let's look at everything in detail.

1. Cleaning rod

Somehow it has long been the custom that for a rifled weapon it must be one-piece, for a smooth-bore weapon it makes no difference, but more often it must be composite. The approach is correct, taking into account the caliber: you never know what can happen in a long tube, the internal diameter of which is less than a centimeter, so the requirements for strength characteristics in the first case are increased.
The cleaning rod material is also different. For a smooth bore, wood and brass are quite suitable; for a rifled bore, only metal, always braided, although bending-resistant and relatively safe stainless steel products are available on sale. Do not use aluminum devices under any circumstances; the oxide covering them has abrasive properties comparable to crushed brick.
Another prerequisite for rifled barrels: the ramrod itself must rotate freely on a bearing installed in the handle, so that the cleaning devices, when moving back and forth, follow strictly the rifling.

Actually, ideally these options look something like this:

On the left is a cleaning rod for smoothbore calibers, two-section, length 86 cm, includes a classic Visher attachment SL. On the right is a cleaning rod for rifled weapons. 35 cal., 9 mm and above, single-section, with bearing, length 91 cm.

2.Visher and patches

The chamber and bevel are sacred cows and must be treated as such. Therefore, the movement of the cleaning rod with the wiping material (patch) always goes in one direction - from the breech to the barrel. The insertion itself must be extremely careful, and the contaminated patch must be removed from the visher upon exiting the barrel. It is very convenient to do this with vishers of modern design.">

Compare: on the left is the classic type, familiar to almost all shooters, on the right is the brass .22/.223 cal.

It is clear that the reverse movement must be no less careful, so as not to damage the rifling ribs at the barrel cut, even with soft brass. This will lead to loss of accuracy of any rifled weapon, including pneumatic ones.
Cutting defects will also not add accuracy to a smoothbore gun. And here, willy-nilly, you will have to use a traditional visher, into the slot of which a cloth of suitable size is threaded and loosely wound.

Somewhat ambiguous devices that serve to protect the chamber, the bullet entrance and the cut of the barrel of a rifled weapon.

The photo shows guides .30 ABS3 and .30 C30.
Let's start with the second one, for cutting the trunk. The scope of its application is extremely narrow, mainly for some models, and all because, as we remember, the barrel is cleaned only from the treasury to the barrel. There are rifles where the manufacturer, as if on purpose, did everything to make access to the breech difficult. But even here it is better not to resort to technology turned 180 degrees.

The guides inserted instead of the bolt, according to authoritative shooters, with rare exceptions do not provide accurate centering of the cleaning rod, since they are made universal for a certain caliber. Meanwhile, each rifle has its own characteristic features. In a word, it’s easier to protect the USM from dripping reagents with a cloth, and center the cleaning rod by eye; the main thing is not to rush or get nervous. Or thoughtfully, again without rushing, choose a guide strictly for your weapon.

4.Brush

There are also a lot of nuances here. In principle, you should remember two things: do not use soft polymer brushes (not to be confused with “puffs”), which generously scatter torn bristles everywhere, and steel brushes for rifled barrels. Hard nylon and copper or brass only. For smooth-stemmed steel, when removing lead and hard carbon deposits, the use of steel mesh devices is quite acceptable.

In the photo: brass and hard nylon brushes, 30 and 12 gauge, as well as a puff, which serves both for lubrication and for removing excess oil.
There are also brushes for cleaning the chamber. As a rule, they come as part of cleaning kits, but they can also be purchased separately, even on a handle.

One more thing important rule: brushes are used only when dry, otherwise they are immediately covered with abrasive particles and only aggravate the process of destruction of the barrel surface.

5. Lifesaver

The final stage of weapon cleaning

Depending on the configuration, we scrub various parts with a stick, sponge, or rag. After the dirt has disappeared, wipe it dry, generously lubricate it with neutral oil, wipe it again and now lubricate it with what is called a thin layer. We drip a little bit into the holes of the smoothbore strikers. It is clear that competition forces manufacturers to move and produce a wide range of solvents and oils. If you want to support them and do everything according to Feng Shui, you can purchase and use lubricants, say, separately for the stem or bolt stops or something else in the same spirit. But, in general, even domestic neutral gun oils are the same “ Golden eagle", are quite functional.

Blessed are the owners of classic break-in shotguns and other kiplaufs, as well as modern semi-automatic rifles. It’s more difficult for the rest - you can’t unfasten the barrel, and here the already mentioned branded cleaning center could be a great help. The basic rule: in a machine or just on a table, the barrel should point down so that all the nasty stuff does not flow into the weapon’s mechanisms.
So, we put a patch on the visher (twist a rag) and in one leisurely movement we push the cleaning rod forward. We discard the contaminated patch and carefully remove the cleaning rod. We alternate patches with brushes (only on dry trunks). We clean the chamber with rotational movements, under no circumstances trying to push a special brush into the bullet entrance. If necessary, treat the barrel with the cleaning compound again.
And so on until we achieve results. Professionals carefully evaluate contaminants, using specialized chemistry depending on their types.

For the average shooter, all this is more interesting in theoretical terms. Or when changing ammunition. So that you can say: “This is dirty!” And don't contact him anymore.
Our task is simple: regardless of whether the copper on the patches turns blue or matte remains of polyethylene in the sleeve are found, we must ensure that the cleaning material at the exit does not differ from what was at the entrance. That's all. Depending on the degree of contamination, all procedures can take ten minutes or an hour.
Finally, the patches emerge from the trunk pristinely clean. And it’s the turn of neutral oil. By and large, we use it to remove not so much dirt as the remnants of cleaning substances, including from metal micropores. Suspicious marks will again appear on the patches. After they disappear, apply a thin layer of neutral oil to the now dry trunk with a lightly lubricated patch, cloth, or powder puff. Or a preservative composition - depending on your goals and objectives. For example, Rust Prevent Corrosion Inhibitor or Elite Hoppe's GO4.

I would like to repeat it again. With the variety of modern weapons, carefully read the manufacturer’s recommendations if you have, say, a stainless or chrome-molybdenum barrel. And select cleaning compounds, especially aggressive ones, strictly in accordance with them. Do not always trust opinions from the Internet; if you read carefully, they often contradict each other. In a word, be careful and careful.

Best wishes for a great hunt

Saltsov Igor

None of the knowledgeable people will argue: cleaning weapons is a necessary matter. Regardless of whether we use it or it just sits in our closet, nevertheless, weapons tend to get dirty over time. Especially, of course, it gets dirty during use: during shooting, while hunting, and if it military weapon– even during the battle.

This raises a whole list of questions: how to properly clean a weapon, what cleaning agents are best to use for this, how often cleaning is necessary, with what devices, etc. If we know why cleaning is needed and apply our knowledge in practice, our weapon will will serve us long and reliably.

How do weapons get dirty?

Naturally, weapons are most intensively contaminated as a result of shooting. It is also clear that the trunk is exposed to the greatest contamination. When fired inside the barrel, a high pressure. Residual products that are formed during the combustion of gunpowder and as a result of ignition of the primer are deposited on the inner surface of the barrel. These products affect the metal, and therefore the barrel, in the most destructive way. In addition, these deposits spoil the polishing of the barrel.

It should be remembered that potassium chloride, which is part of the primer, is much more harmful to weapons than gunpowder residues. When fired, its particles come into contact with the surface of the barrel, which is why at the points of contact the steel loses its original properties and becomes fusible. The powder gas generated during the shot melts the steel fragments and pushes them out. As a result, the inner surface of the trunk becomes rough, and a rash and small shells form on it. This process is known to gun owners as “bore-flashing.”

And this is not all the harmful effects of potassium chloride. It also has the property of drawing atmospheric moisture into the barrel, which causes the steel in the barrel bore to corrode and rust. In addition to potassium chloride, the primer contains mercury, the residues of which penetrate deep into the metal, resulting in microcracks that contribute to further deterioration of the barrel.

Due to the heating of the barrel during the shot and cooling after it chemical reactions, promoting the height of the trunk, last from 3 to 5 days. If at the same time the weapon is fired intensively every day, then due to the friction of the bullet passing along the barrel, the process only intensifies. And it will get worse until the weapon is cleaned.

There are three main stages of cleaning weapons:

pour alkaline oil (solvent) into the inside of the weapon;
clean the weapon;
lubricate the weapon.

Of course, when cleaning weapons of various systems, there are many features that must be taken into account.

Cleaning rifled weapons

Basic rules for cleaning rifled weapons:

Rifled weapons should be cleaned in the following sequence: first the breech, then the muzzle. That is, in accordance with the direction of flight of the bullet;
The cleaning rod should also move in the same direction - from the breech to the muzzle. In this case, it is recommended to change the patch (a special napkin rolled onto the wipe, called a visher) more often. The patch is a disposable device, so it is not recommended to use it repeatedly;
It is not recommended to move the cleaning rod for cleaning weapons in the “back and forth” mode. This may cause scratches inside the barrel. Moreover, the brush and patch are easily clogged with particles deposited on the walls of the barrel;
The brush for cleaning weapons should be chosen not soft, but hard. Soft bristles very quickly become clogged with hard carbon deposits settled inside the barrel, and it is very difficult to remove it from a soft brush. On the contrary, a brush with a stiff brush is much more effective in this sense, since it cleans the inside of the barrel more reliably. In this case, you need to ensure that the brush remains dry (as well as the patch), otherwise, again, residual particles in the barrel bore will stick to them;
It is advisable to clean your weapon immediately after shooting. It is highly recommended not to postpone cleaning until the next day. The reasons for this requirement were discussed above;
It is necessary to periodically clean the weapon even if no shooting has been done from it. In this case, the lubrication is not so intense;
If the weapon was fired, then, as stated, it should be cleaned immediately after firing. After 2-3 days, the weapon must be cleaned again, and after another 2-3 days - a third time. And only then can rifled weapons be stored for a long time, but it should be remembered that even during long-term storage they must be periodically cleaned;
It is most necessary to clean the muzzle part and the bullet entrance - as the most “easily damaged” parts of the barrel;
When cleaning rifled weapons, it is very undesirable to use a variety of “homemade” products: homemade compounds, lubricants not intended for weapon cleaning. You cannot use homemade alkaline compounds; you also cannot immerse the weapon or its individual parts in highly alkaline solutions. Such an amateurish approach to cleaning weapons can simply ruin the weapon;
After cleaning, the gun barrel, as well as all cleaned components and mechanisms, must be lubricated with gun oil.

To clean your weapon more efficiently, you can use a stand or a weapon cleaning machine. These are special devices on which the weapon is conveniently fixed. In addition, the machine and stand have special niches for storing gun oils and other cleaning and lubricating products. At the same time, the stand for cleaning weapons is very compact, so if you wish, you can take it with you even when hunting or to shooting sports competitions. You can make it yourself, or you can buy a branded one.

Cleaning smoothbore weapons

Smoothbore weapons, like all other types, need to be cleaned. It is important to know the frequency of cleaning such weapons. There are many opinions on this matter, but most knowledgeable people States that smoothbore weapon must be cleaned at least monthly - even if it has not been fired at or taken from the safe.

However, there are situations when weapons need to be cleaned more often:

After purchasing a gun – especially a new one;
After the gun has been zeroed;
After each day spent hunting;
After the hunting season is over.

After purchasing the gun, you need to clean it to remove the factory grease, and also check how the gun is assembled and whether there are any defects in it. During the zeroing process, the gun must be cleaned after each shot. This will help determine how accurate the gun is. When it comes to cleaning a gun during a hunt, everything is clear and without explanation: it is during hunting that the gun gets dirty the most. Well, in " dead Season» the gun is cleaned for preventive purposes: during storage in the closet, moisture may accumulate in the gun.

Smoothbore weapons are cleaned in the following sequence:

First, the barrel is broken or dismantled (depending on the design of the weapon);
A brush screwed onto a cleaning rod is passed over the inside of the table to remove substances harmful to the weapon that were formed during shooting from the barrel;
You need to change the brush on the cleaning rod to a brush into which the patch is inserted, and with the help of such devices the barrel is cleaned until there are no signs of soot or soot left in it. In this case, the patch needs to be changed periodically;
If several rags have already been replaced, but traces of burning are still not completely removed, then in this case the rag should be moistened with turpentine or kerosene;
After the contamination from the barrel has been completely removed, a brush with stiff bristles is put on the cleaning rod, onto which a universal or neutral lubricant is previously applied, and the entire inside of the barrel is covered with this lubricant;
From the outside, dirt is removed from the entire body of the weapon, after which the body must be lubricated with a thin layer of lubricant;
The wooden parts of the weapon are also cleaned of dirt and lubricated;
After this, the gun must be collected and stored in a safe.

When cleaning, care must be taken to ensure that no moisture gets into the barrel. If a weapon is cleaned in winter, then in this case the gun is allowed to “sweat” by wrapping it in a warm rag.

However, all this is good if the weapon is not rusty, but if it has already begun to rust, then more radical means are needed. In this case, the barrel is cleaned using a metal brush and a hard brush. In this case, the brush and brush, as well as the rod for cleaning the barrel, are moistened with dehydrated kerosene. If there is a lot of rust and it is old, then kerosene should be poured into the barrel, the barrel itself should be plugged with a tight plug, and everything should be left like that for 24 hours. After this, the barrel needs to be cleaned using the same brush and brush.

But if rust has formed on the outside of the weapon, then waterproof glue can come in handy. First, use a hot soda solution to wash off all the grease from the gun. The glue is then diluted in hot water, and this substance is applied to the surface of the weapon - to the part where the rust appeared. The glue dries instantly, after which a universal lubricant is applied to the treated surface.

Even if such a product does not cope with the rust, you can try to remove it by preparing the following solution:

Ammonium sulfate – 28 g;
Ammonium carbonate – 13 g;
Ammonia water – 170 g;
Distilled water – 100 g.

The prepared solution must be poured into the barrel, plugged into the barrel on both sides, hold the solution in the barrel for half an hour, then remove it, wipe the barrel dry and lubricate it with alkaline oil.

Airgun cleaning

Pneumatics also need cleaning. Not as often, of course, as rifled or smooth-bore weapons - but still less so. The air rifle also gets clogged, and in addition, its charges also leave a mark inside the barrel. In addition, pneumatic barrels are not as high quality as those of other weapons; the steel used to make them is relatively soft, and for this reason such barrels rust easier and faster than those of hunting rifles.

Cleaning an air rifle is necessary in the following cases:

Between 100 and 200 shots;
When the rifle’s accuracy decreases (the rifle begins to “spit”);
When smoke and sparks are visible from the barrel when fired.

You can start cleaning the pneumatic barrel from either end. The process of cleaning the “air” consists of four main stages: removing lead deposits inside the barrel, degreasing the barrel, drying and lubrication. After this, the cleaned weapon must be lubricated. When lubricating a pneumatic barrel, some rather specific nuances should be taken into account.

In principle, lubricant for an air gun is needed “to the extent”, but still the charge moves through a lubricated barrel more easily. However, if the barrel is over-lubricated, the accuracy of the combat will decrease in this case (the rifle, again, will “spit” in different directions). It is best to lubricate the barrel with some neutral gun oil. Moreover, in an extremely thin layer.

Cleaning 12 (16, 20) gauge weapons

To clean 12, 16 and 20 gauge weapons, in general, you will need the same set of tools and tools as described above. And the sequence of cleaning and lubricating the barrel and individual components is the same.

The only “know-how” here is that many experts and practitioners advise cleaning the barrel of a gun not with a rag, but with a ball made of toilet paper. Such a ball is driven into the barrel and pushed along the entire length of the barrel using a cleaning rod with a brush mounted on it. It is claimed that toilet paper is much better at cleaning the barrel than rags. For perfect positive result It is recommended to clean it with several of these balls.

Weapon cleaning products

Throughout its existence firearms Innumerable devices have been invented for cleaning it, ranging from the most primitive to the most modern, which can be found in the catalog. We won’t talk about ancient methods like cleaning the bore with crushed bricks here. Let's talk about some of the most popular modern means for these purposes:

German-made gun oil Ballistol 50 ml (liquid);
Gun oil of the same production Gunex 2000 200 ml in the form of a spray. Cleaner for cleaning dirt inside the barrel Robla Solo MIL 100 ml in liquid form. Made in Germany. All three of these products are included in the kit with which you can clean and preserve weapons;
For the same purposes, there is also an American BIRCHWOOD-CASEY Value Pack;
Foam for cleaning weapons. Actually, the global chemical industry has produced a lot of foam samples for these purposes. For example, Armatech 210 ml made in Russia. Or - Schmeisser 200 ml made in Germany. And so on;
A product for cleaning weapons from soot and soot, as well as for protecting against corrosion, Ballistol Robla Solvent. The solvent is available in the form of an aerosol, and perfectly cleans the barrel - especially when using charges with black powder. In addition, the solvent has excellent corrosion resistance;
A set for cleaning weapons with a special flexible snake, and weapons exclusively of 12 gauge. Made in the USA;
Alkaline composition "Taiga" made in Russia. It is remarkable because it can be used to effectively clean any weapon - rifled, smooth-bore, pneumatic. At the same time, its cost is very small.

This list could be continued, but it’s better to look at the catalog and choose a product that suits your taste and budget.

To summarize, we can say that cleaning weapons is the most important condition so that it serves faithfully for many years.

If you have any questions, leave them in the comments below the article. We or our visitors will be happy to answer them

A rod for cleaning the barrel of a weapon. Modern methods for cleaning rifle barrels

Professionals and amateurs: the difference in approaches

Stages of cleaning weapons